OPBOX 2.1 is a complete ultrasonic testing device, suitable for all ultrasonic measurements and due to many additional digital inputs/outputs and internal processor it can be used as a controller for more complicated devices.
Opbox 2.1 can work together with devices like multiplexers or scanners.
The box has an implemented one channel pulser & receiver and can be used with one or two transducers (one is sending, and the second one receiving).
The system allows to buffer many acquisitions in internal memory and forward whole packet of data to control application.
In this way, the high throughput of data reading from the device is obtained.
-Low noise preamplifier (0.74 nV/√(Hz))
-High gain up to +89 dB
-Switchable analog filters
-Support fast TGC (time gain compensation)
-2 signal inputs PE and TT
-Input attenuator (-20dB)
-Input Impedance 50 Ohm, 10pF
-10 bit A/D Converter
-100MHz sampling frequency, 8bit samples
-Up to 512k x 16bit samples memory
-Delay settings up to 65535 sample periods
-various triggering mode
-BNC or Lemo analog connectors
-dimensions: L 100mm W 82mm H 32mm
-DB15 connector: I/O lines 6 Inputs and 6 Outputs
-USB-2.0 High Speed (480MBps)
-Power supply: USB connector <500mA
Input Amplifier Gain: -31dB to 65dB (step 0.5dB)
Switchable preamplifier: +24dB
Switchable Attenuator: -20dB
Input Range: ±275mV
(±2.0V with Attenuator -20dB)
Full Bandwidth: 0.5 MHz - 25 MHz (-3dB)
Switchable Filters(-3dB): 0.5 - 6MHz, 0.5 - 10MHz, 0.5 - 15MHz, 0.5 - 25MHz, 1 - 6MHz, 1 - 10MHz, 1 - 15MHz, 1 - 25MHz, 2 - 6MHz, 2 - 10MHz, 2 - 15MHz, 2 - 25MHz, 4 - 6MHz, 4 - 10MHz, 4 - 15MHz, 4 - 25MHz
Pulse Voltage 0V to 360V (positive pulse)
Charging Time adjustable from 0 to 3.1us in 0.1us steps
Fall Time <= 20 ns
Bandwidth up to about 50MHz
Output impedance < 1 Ohm
A/D data acquisition:
Resolution 10 bit (8bits are stored)
Maximum input voltage: ±0.5V;
Sampling Frequency(MHz) 100; 50; 33.3; 25; 20; 16.7; 14.3; 12.5, 11.1; 10; 9.1, 8.3; 7.7; 7.14 and 6.67
Data Buffer 1 to 256k samples
Measuring frame delay: 0 to 65535 sample periods
PRF up to 10 000
Hardware data processing:
Data representation: RF, Absolute;
Measurements in defined frames: 3 peak detectors;
3 level comparators - modes of transition detection:
Level, Rising, Falling, Transition.
DAC (TGC) with arbitrary function generator:
Resolution: 8 bit
Max. gain changing: 48dB pro step
2 incremental encoder modules;2 TTL inputs
Counter modules for incremental encoders:
Two 32bit modules with CHA, CHB and IDX inputs;
Programmable input modes: 1X, 2X, 4X;
Programmable triggering on position;
PE (sending&receiving) BNC or Lemo;
TT (only receiving) BNC or Lemo;
6 inputs for 2 Incremental encoder channels (A, B, Index signal) or general purpose lines;
6 general purpose outputs;
Trigger output signal (Sync Out);
+5V fused supply for powering external devices.
We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
Copyright © 1989 - 2020 Optel. All rights reserved.
Limited, registered in the Companies Register by the regional court Wroclaw Fabryczna, VI Industrial Section of KRS, under the number 0000124439,
NIP: PL 8981047033, REGON 008375538, operating capital 364,500 PLN